If you own a bidet, you know how convenient and hygienic it can be; however, sometimes issues might arise that require some troubleshooting. If your bidet has stopped working properly, or if the water pressure is low, then it may need a reset. Fortunately for you, this is an easy task!
In this blog post, we’ll explain exactly how to reset bidet so that you can get back to enjoying its cleanliness and convenience with ease. Keep reading to learn more and get started on the path to better hygiene today.
12 Step-by-step Guidelines on How to Reset Bidet
Step 1: Turning Off the Power Supply
Turning off the power supply can usually be done from a wall switch or breaker box, depending on how your unit is set up. More advanced bidets may also have a power button on the unit itself. If so, press that button to turn it off.
Remember to always disconnect the power prior to doing any work on your bidet! This is an important safety measure. You should also make sure that any water lines have been disconnected from the bidet before proceeding.
Step 2: Disconnect Water Lines
Disconnect the hot and cold water supply lines, if applicable. Once all of the lines have been disconnected, open up the valve located on the bottom of the bidet. This will allow any air pressure to be released and water to escape, if necessary. It is important to make sure that all of the water has been drained in order for the reset process to be successful.
Step 3: Open a Water Faucet
Slightly open a hot and cold water faucet near the bidet system. This will help to reduce any pressure that may have built up in the water lines. It is important to note that this should be done slowly and carefully, as too much pressure can damage both the faucets and the bidet system.
It is also important to make sure that the faucets are open before you reconnect them to the bidet. Otherwise, the pressure could be too high and cause damage.
Step 4: Test the Pressure
Test the pressure of each line with a pressure gauge. To do this, attach the gauge directly to each line and turn on each one individually. This will allow you to get an accurate reading of how much pressure is in each line. If either line exceeds 40 PSI (pounds per square inch), then it needs to be adjusted accordingly.
But, if both lines read within the acceptable range (25-30 PSI), then you can move on to the next step.
Step 5: Adjust the Pressure
Adjust the pressure regulator if necessary. This is located on the main water line and is used to control the amount of pressure in the lines. If you find that either one of your lines has too much pressure, then simply turn the regulator down a few notches until it reaches an acceptable level. If the pressure is too low, then adjust it accordingly.
It is important to note that you should only make small adjustments at a time in order to avoid sudden changes in pressure.
Step 6: Turn On Each Line and Test Again
Once you have made any necessary adjustments, turn on each water line individually and test again with a pressure gauge. This will ensure that no excessive pressure exists in either line before proceeding to the next step. It is also important to make sure that all of the lines are turned off before you begin reconnecting them back to the bidet system.
Step 7: Reattach All Water Lines
Once you have completed all of the above steps, it’s time to turn the power back on and reattach any water lines connected to the bidet system. But before doing so, it is important to make sure that the pressure levels are still at the desired level by testing with a pressure gauge one more time. This will ensure that the reset has been successful.
Step 8: Turn on Each Line Individually and Test Pressure Again With a Pressure Gauge
Again, make sure that no excessive pressure exists in either line before proceeding. If you find that the pressure has changed since your last test, then adjust the regulator accordingly and test again before proceeding. But, if all is good, then you can enjoy your reset bidet system!
Remember to always follow safety precautions and make sure that any water lines are disconnected before beginning the reset process.
Step 9: Open Up the Valve
Open up the valve located at the bottom of the bidet system. This will allow air to be released and ensure that everything is working properly. Make sure to keep an eye out for leaks during this step as well! It is important to make sure that all of the water has been drained in order for the reset process to be successful.
If you have any questions about how to reset a bidet, please contact a professional for assistance.
Step 10: Test the Water Temperature
Test the water temperature with a thermometer or thermostat. To do this, simply attach the thermometer or thermostat to the bidet and turn on each line individually. This will allow you to check that the water is reaching a comfortable and safe temperature before use.
Before you use the bidet, make sure to turn off all water lines and test again with a pressure gauge to ensure that no excessive pressure exists in either line.
Step 11: Check All Connections for Leaks
If you notice any leaking during your reset process, then it’s important to stop immediately and tighten up all connections. Make sure to also look for any loose screws as well! It is also important to make sure that all connections are properly secured before using the bidet. So, make sure to double check this before using it! It’s better to be safe than sorry!
Step 12: Test Everything Out
After all of the above steps have been completed, it’s time to test out your new bidet system. Turn on each line individually and test out the water pressure, temperature, and other features to make sure that everything is working properly. You should also check for any leaks during this step. If no issues are found, then you can begin using your newly reset bidet system!
Remember to always follow safety precautions and turn off all water lines when not in use. It’s also important to regularly inspect and maintain your bidet system so that you can enjoy it for many years to come.
Once you have completed all of the above steps, your bidet should be reset and ready to use! It’s important to regularly check your bidet for any signs of damage or leaks in order to keep it in good condition over time. Thanks for reading this guide on how to reset a bidet – we hope it was helpful!
Do You Need to Use Professionals?
In general, it is not necessary to use professionals to reset your bidet. However, if you are having any trouble during the reset process or there are any signs of damage to the system, then it is best to seek professional help.
A qualified plumber can inspect and repair any potential issues with your bidet and ensure that everything is running smoothly. If you are unsure about any steps or the overall process, then it is always best to seek help from a professional.
Frequently Asked Questions
Q: How Often Should I Reset My Bidet?
A: It is recommended to reset your bidet every six months or so to ensure that it is in good working condition. This will help you avoid any unnecessary repairs that may occur due to an improper reset process.
Q: What Happens If I Don’t Reset The Bidet?
A: If you don’t reset your bidet periodically, then there is a chance that the water pressure could become too high and cause damage to the system. This could lead to costly repairs or even a complete replacement.
Q: Is There Anything Else I Should Do Before Resetting My Bidet?
A: It is always a good idea to check for any signs of damage or leaks before resetting your bidet. This will help ensure that everything is in working order and ready to use once you have finished the reset process.
Conclusion
Taking the time to reset your bidet can be a great exercise in learning how to reset bidet and taking an active role in its maintenance. You don’t always have to call in a plumber or even understand the full mechanics of a bidet at all, however.
With just a few steps, you can easily reset the device on your own and get back to enjoying its many benefits. That concludes our guide to how to reset a bidet. If you ever encounter any difficulties along the way, contact BidetsPlus directly for assistance!
Our team is trained and willing to help with any issues that may arise while using and caring for your bidet seat or washing unit.
